Fluid Flow & Aerodynamics
why things fly, and why the usual explanation is wrong
The collection

Every essay — page 62

Page 62 of 62, continuing through the fields in the same order.

Flows and fields Ideal flow Circulation and lift Viscosity Regimes and numbers Compressible flow Transition and turbulence Fluids at work What is taught wrongly Series Concepts Regimes Refutations Search

Viscosity

The thin layer next to a surface that ideal flow ignores, and which supplies drag, separation and the wake.

The same cap costs a rising bubble a quarter of its speed and a migrating one four-fifths. Speed as a fraction of the clean bubble's against the half-angle of a stagnant cap over the rear: for a bubble migrating in a temperature gradient, and for the same bubble rising under its weight. A 90° cap leaves the rising bubble 74 per cent of its speed and the migrating one 21 per cent; a 120° cap, 68 and 4. The rising bubble can only fall to a rigid sphere's two-thirds; the migrating one falls to nothing.

A cap that slows a rising bubble stops a migrating one

Surfactant swept to the back of a bubble holds the surface still there, and for a bubble rising under its weight the worst this can do is turn it into a solid sphere and cost it a third of its speed. A bubble migrating in a temperature gradient has no such floor. Its own surface is the engine, and a cap removes the engine as well as raising the drag. A cap over the cold hemisphere leaves a rising bubble three-quarters of its speed and a migrating one a fifth; a cap of 120° leaves the migrating bubble four per cent. The surfactant it takes is set by the tension difference that drives the migration, and that is tiny.

6 figures A slow bush leaves the bearing hunting, a sixth faster. The film's mean temperature excess over two cycles of a bearing hunting under a derating of 0.2 with a fifth of the housing's excess reaching the bush, for a bush that follows the housing instantly and one ten housing times slow. Both jump between a cool film and a hot one; the instant bush's period is 0.347 housing times, the slow bush's 0.291. The slow bush holds the walls at the cycle's mean, and the film's jumps are the same size.

A slow bush quickens the hunt it cannot start

A bearing's bush warms with its housing and makes the drive stiffer, and past a coupling of about a third it stops a derated bearing hunting. Give the bush a time of its own and the obvious fear is that the lag reopens the hunt. It cannot: whether a bearing hunts is decided by where its equilibrium sits, which no lag can move, and a lag on a positive link cannot make a settled state oscillate. What a slow bush does change is the hunt itself, which runs a sixth faster.

7 figures A free jet keeps its momentum; a wall jet keeps the flux of its momentum flux. Each quantity against distance, relative to its value at 2 cm, on logarithmic axes. The free jet's momentum flux is constant and its volume flux grows as x^(1/3). The wall jet's momentum flux falls as x^(−1/4) — the wall's shear takes it — while its volume flux grows as x^(1/4), and the one thing it conserves is Glauert's ∫u(∫u²)dy, the flux, through each height, of the momentum flux carried above it.

A jet along a wall keeps the flux of its momentum flux

A jet in open fluid keeps its momentum and gathers fluid as it goes. Blow the same jet along a wall and the wall takes its momentum away as drag, so it keeps neither. What it keeps is stranger: the flux, through each height, of the momentum flux carried above that height. That one invariant fixes everything else — the jet thickens as the three-quarter power of distance, slows as the inverse square root, and gathers fluid as the fourth root, more slowly than the free jet's cube root.

7 figures Hold the nozzle further from the plate and the jet arrives slower but leaves a stronger wall jet. For a laminar jet from a 2 mm slot at 5 cm/s in water, against the nozzle's distance from the plate, each over its value at 10 cm: the arriving centreline speed, which falls as h^−⅓; the inherited invariant F = 3KQ/32, which grows as h^⅓ because the jet has gathered fluid; and the wall jet's peak speed a metre along the plate, which grows as h^⅙. At 2 cm the arriving speed is 1.71 of its value at 10 cm and the far wall jet 0.765; at 2 m, 0.368 and 1.65.

A jet striking a plate leaves a stronger wall jet the further it travelled

A plane jet that strikes a wall splits into two wall jets, and each keeps not the jet's momentum but Glauert's flux of momentum flux. Turned without loss at the stagnation point, each half arrives laid along the wall with its axis on the wall, and its invariant is the momentum it brought times the fluid it had gathered on the way: F = 3KQ/32. Hold the nozzle further away and the jet arrives slower but leaves a stronger wall jet, by the cube root of the distance — and the wall jet takes a distance of about the Reynolds number in jet widths to forget it was ever free.

6 figures The paint pushes a scraper off the wall, and roughly as one over the square of the angle it is held at. The force the fluid exerts on a still blade at angle α to a wall sliding into the corner, per unit span over μU ln(R/ε): its component pushing the blade away from the wall and the size of its component dragging it along with the wall, towards the apex. At 10° they are 196 and 22.9; at 45°, 8.56 and 4.88; at 90°, 1.36 and 2.14; at 150°, 0.0757 and 0.924.

A scraper held flat is pushed off the wall it scrapes

A corner stirred from far away fills with an endless sequence of eddies. Drive the corner at the corner instead — let one of its walls slide under a still blade, as paint slides under a scraper — and the eddies vanish: every streamline turns once, and the stress rises into the corner without limit. G. I. Taylor solved it in 1962. The paint pushes the blade away from the wall with a force that grows as one over the square of the blade's angle, so a blade held flat rides up on what it was meant to remove, and the force is finite only because something too small to appear in the problem ends the corner.

6 figures A cut deeper than the film's window flips the film twice a cycle; a shallower one leaves it where it is. A protection that trips at a housing excess of 3.0 and resets at 2.6, against the depth of its cut: left, the film's jumps between its branches per protection cycle; right, the cycle's period in housing times. The film has both branches between 0.6496 and 0.7279 of full drive, so a cut past 0.35 leaves it only the cool one. cut 0.3: never resets; cut 0.34: 0 flips, period 1.85; cut 0.36: 2 flips, period 0.767; cut 0.6: 2 flips, period 0.756.

A trip deeper than the film's window flips the bearing twice a cycle

A smooth derating acts on a bearing's housing temperature as it stands. Most real protections trip instead: they cut the motor at one temperature and restore it at a lower one, a hysteresis of their own laid on top of the film's. Whether the oil then jumps between its cool and hot states is decided by one comparison — the cut's depth against the width of the film's window — and past it the protection's own band sets the rhythm. A trip never lowers the film's peak at all; it only protects the housing, and a deep one buys that with a plunge to the cool branch twice in every cycle.

7 figures At a levitator's own thermal numbers every gas lifts within a few per cent of the isothermal film; only a thick, slow film lifts more. The mean pressure excess of a trapped film squeezed by a quarter of its gap, over the isothermal film's 0.0328 of ambient, against the thermal number ωh²/κ, for three ratios of specific heats; dots, the six gases of a 20 kHz, 20 µm levitator at one atmosphere: helium 1 at Ω = 0.29; air 1.002 at Ω = 2.4; argon 1.005 at Ω = 2.5; carbon dioxide 1.005 at Ω = 4.7; xenon 1.042 at Ω = 7.9; sulphur hexafluoride 1.003 at Ω = 16. At Ω = 300 a monatomic gas lifts 1.21 times the isothermal film, against the 1.69 a core on the walls' mean temperature would give.

A levitator lifts by its amplitude, not its gas

A squeeze-film levitator holds its load up by the mean of a pressure that swings symmetrically about nothing, and the gas in the gap was expected to decide how much: a gas that cannot shed its heat of compression in time is stiffer, so it should lift more. Solved to every order in the amplitude, with the heat crossing the gap, it barely does. At a levitator's own thermal numbers every common gas lifts within a few per cent of the isothermal film while its losses differ several-fold, and even a gas far too slow to shed its heat lifts only a fifth more, because the walls quietly pump heat out of it and cool its middle.

6 figures A round jet held further from the plate arrives slower in proportion and leaves a radial wall jet stronger in proportion. For the round water jet from a 2 mm nozzle, against the nozzle's distance from the plate, each over its value at 10 cm: the arriving centreline speed, the radial invariant F = Kνh/(2π) it hands on, and the radial wall jet's peak speed 5 cm from the stagnation point; dashed, a plane jet's speed and invariant for comparison. At 40 cm the round jet arrives at 0.25 of its speed at 10 cm and hands on 4 times the invariant, and its wall jet runs 2 times as fast; a plane jet's invariant would have grown 1.59 times.

A round jet hands its wall jet a strength proportional to its throw

A round jet striking a plate spreads into a radial wall jet, and like the plane jet before it, the wall jet keeps not the jet's momentum but Glauert's flux of momentum flux — the momentum the jet brought times the fluid it gathered on the way. A round jet gathers fluid at a rate set by the viscosity alone, eight π ν per metre of travel, whatever its strength. So the invariant it hands on grows in exact proportion to the distance it was thrown, where a plane jet's grew as the cube root: hold the nozzle four times further away and the wall jet is four times as strong and runs twice as fast.

6 figures Two spheres settle faster together than apart, faster in line than side by side, and still faster at thirty radii than either alone. The settling speed of a pair of equal spheres over a single sphere's, against the distance between their centres in radii: along the line of centres, exactly (the bispherical solution) and by Batchelor's far-field series; across it, by the series; dashed, each sphere's Stokeslet alone, 1 + 3/(2ρ) and 1 + 3/(4ρ). Touching in line the pair falls 1.55 times as fast; at 5 radii, 1.286 in line and 1.154 side by side; at 30, 1.05 and 1.025.

Two spheres settling at a slant keep their slant for ever, and three do not

Two equal spheres settling through a viscous liquid fall faster together than either alone — half as fast again if they touch in line, and still five per cent faster thirty radii apart. Slanted, the pair drifts sideways as it falls, by up to three and a half degrees, and keeps the slant, the separation and the drift for as long as it falls: the two spheres always move with exactly the same velocity. Release a third and the shape is lost at once, the middle sphere drawing ahead and the outer two closing in behind it. What a pair keeps and a trio does not is a statement about symmetry, and reciprocity is half of it.

6 figures A sphere two per cent larger overtakes its neighbour round a path that is its own mirror image, and leaves at the offset it came in at. The centre of a sphere two per cent larger than its neighbour, relative to the smaller sphere, as it overtakes it in a viscous liquid, from four horizontal offsets; the circle is the distance at which they would touch. Each path bulges outward as it passes and is symmetric about the smaller sphere's level: from 0.85, 1.5, 2.5, 4 radii the larger sphere leaves at 0.8499, 1.5, 2.5, 4, after closest approaches of 2.27, 2.83, 3.74, 5.15 radii.

A larger sphere overtakes its neighbour and leaves on the line it came in on

Two equal spheres settling together never change their shape. Make one of them two per cent larger and the pair becomes an encounter: the larger sphere sinks past the smaller round a path that bulges out and comes back, slowed sixteenfold at contact but never stopped, and it leaves at exactly the offset it arrived with. The smaller sphere swings seven radii sideways while the larger is above it and gives every radius back while the larger is below. In Stokes flow, meeting a neighbour displaces nothing — unless the spheres touch, and a hundredth of a radius of roughness is enough to make every touching path leave on the same line.

6 figures Pressed with one load, a steeper blade leaves a thinner film, and without a land a steep one cannot float at all. The film a loaded scraper leaves on the surface, in micrometres, against the angle its face makes with the surface, at a load of 100 N per metre of span on an ink of 0.1 Pa·s moving at 5 m/s: with a flat land 0.1 mm long under the edge, and with none. With the land the film is 110 µm at 10°, 1.69 at 30° and 0.268 at 60°. Without one it is the whole gap, 145 µm at 8°, and above 44° the gap the load needs is below a ten-thousandth of a nanometre: the edge is in contact.

A pressed blade floats on its land and leaves half the gap behind

A scraper or a doctor blade is not held at a gap; it is pressed on with a load, and it rises until the liquid it lets through carries that load. Without a flat land under its edge the liquid can carry it only through the corner's logarithm, so the gap falls exponentially with the load, and a blade steeper than about forty-four degrees cannot float at a working load at all — its edge is in contact. Give it a land a tenth of a millimetre long and the film becomes half the gap, falls as one over the load, and is a quarter of a micrometre at sixty degrees. The land is also why a blade's film grows as its edge wears.

6 figures A drop on a plate too hot to touch lives a hundred times longer than one on a merely hot plate. The lifetime of a drop of 2.5 mm radius against the plate's temperature, in contact (nucleate boiling) and on its film. At 130 °C, in contact, 11 s; on its film at 210 °C 1062 s, and at 500 °C 229 s. Where the two branches meet depends on the plate: Leidenfrost's point on polished metal is about 200 °C for water, and on a rough plate can be well above it.

A Leidenfrost drop floats on a bearing it feeds itself

A bead of water on a hot pan vanishes in seconds, unless the pan is much hotter, when it skates about for minutes. Between the drop and the plate is a film of its own steam a tenth of a millimetre thick, and that film is a lubricated bearing with no shaft and no pump: its supply is the drop's own evaporation, which keeps it thin where it is thick and thick where it is thin. Its thickness obeys a fourth root of everything. On a plate too hot to touch, the drop's lifetime is a hundred times what it is on a plate that is merely hot.

6 figures