Every essay — page 54
Flows and fields Ideal flow Circulation and lift Viscosity Regimes and numbers Compressible flow Transition and turbulence Fluids at work What is taught wrongly Series Concepts Regimes Refutations Search
Viscosity
The thin layer next to a surface that ideal flow ignores, and which supplies drag, separation and the wake.
A motor turns the runaway into a jump
A self-heating oil film has a fold at fixed stress and none at fixed speed, and a real motor is neither: its torque falls along a line as its speed rises. Put that line across the film's own torque–speed curve and the runaway disappears for any motor at all. What replaces it depends on the line's slope. A drive softer than one fourteenth of the cold oil's resistance jumps to a hot state and keeps a memory of the load; a stiffer one does neither. And the boundary between the two falls exactly where the motor is turning at a quarter of its no-load speed, which no motor near its rated speed can reach.
A torn film still pulls
A sphere bouncing off a wall under liquid has to climb back out through the film it squeezed, and the film pulls it back with a suction no real liquid can supply. Let the liquid cavitate and the obvious guess is that the sphere escapes the torn part of the film for free. It does not. The liquid round the vapour disc goes on pulling, and the disc itself holds the full tension over its area, so a film that tears at five times the contact gap saves a third of what the guess says — and the rebound threshold moves by five per cent where the guess said a third. At an atmosphere, in the liquids the threshold was measured in, it barely moves at all.
A rotor's inertia slows the jump and cannot make it ring
Give the motor driving a self-heating oil film a rotor that has to spin up, and there are two clocks: the film's diffusion time and the rotor's. Two clocks are what an oscillator is usually made of, and this pair cannot make one. Every eigenvalue stays real at every inertia, because the film and the rotor only ever push each other the same way. What inertia does instead is add its own delay to the film's, and in a real machine, where the rotor is hundreds of times slower, the delay past the fold is almost entirely the rotor's.
A thin fibre coats by its own radius, and beads by it
A plate drawn out of a bath carries a film set by the capillary length, the size at which surface tension and gravity balance. A fibre thinner than that length carries a film set by its own radius instead, often a tenth of what the plate's law promises — and the same radius then decides how quickly that film gathers into beads. The faster the fibre is drawn, the thicker its coat and the shorter the length of it that comes out smooth.
A slow sensor makes the bearing cycle
Derate the motor driving a self-heating oil film on the temperature of its housing, which warms over minutes, and a protection meant to hold the bearing cool instead makes it cycle for ever: jump hot, warm the housing until the hot state is lost, drop cool, let the housing cool until the cool state is lost, jump again. The period belongs to the housing, the amplitude belongs to the film, and the derating strength decides only whether the cycle happens at all.
The heat of a squeeze leaves across the gap
Squeeze a film of air and it warms, and whether that heat reaches the walls in time decides whether the gas is compressed isothermally or adiabatically. The natural estimate has the heat leaving the way the gas does, along the disc, and puts the thermal crossing beside the viscous one. It leaves across the gap instead, a distance hundreds of times shorter, so the crossing sits decades away — and when a film does reach it, what it gains is not stiffness but a second band of loss.
The largest bulk viscosity is the first to expire
A bulk viscosity is not a separate property of a gas. It is the time a molecule's internal motion takes to catch up with a compression, multiplied by the pressure and by how much heat capacity lags, and read from below that time's frequency. So the coefficient that is largest is the one that stops being a coefficient soonest: carbon dioxide's fifteen-hundred-fold value is ten per cent wrong at 24 kHz, and on Mars it is two speeds of sound in the audible band.
A bulk viscosity holds a shock together until it splits
Carbon dioxide's bulk viscosity, fifteen hundred times its shear viscosity, is a vibrational relaxation seen from below its frequency, and a shock is where that description is tested hardest. Carried through a steady shock, the relaxation reproduces the coefficient exactly for the weakest shocks. At a pressure rise of nine and a half per cent the shock outruns the frozen sound speed and splits into a jump and a tail, and the coefficient then draws a shock that does not exist.
A warm bush stops the bearing hunting
A bearing whose motor is derated on its housing's temperature can hunt, jumping between a cool film and a hot one on the housing's clock. Let the bush warm with the housing, and a second feedback joins the first, of the kind that usually makes things run away. It does the opposite: a warm wall is a stiffer drive, the stiffening closes the S the cycle runs round, and past a bush coupling of about a third the bearing settles, warm and derated, however the protection is set.
The gas sets a squeeze film's loss, not its stiffness
A squeeze-film levitator wastes part of every cycle as heat that crosses the gap, and the gas and its pressure decide how much. Fill one levitator with six gases at one atmosphere and its stiffness hardly changes while its loss nearly doubles from helium to xenon. Raise the pressure and every gas stiffens towards a peak near ten atmospheres. Helium wastes least at any stiffness up to a hundred newtons; above that, only the heavy monatomic gases get there.
A thousandth of a monolayer holds a bubble still
A clean bubble rising slowly through water feels two-thirds of a rigid sphere's drag, and real bubbles almost never do, because surfactant swept to the rear holds the surface still over a cap there. Solving the flow with the cap in it shows how little that takes. The drag runs ahead of the area covered — half-way to rigid with a third of the surface held — and the surfactant needed is set by the viscous stress, not by the surface tension. For a bubble a tenth of a millimetre across, a thousandth of a monolayer, spread as a cap, makes it rise within a few per cent of a solid ball.
A point force makes a jet only when it is strong
Push on a fluid at one point and there is an exact solution of the full Navier–Stokes equations for what follows, at any strength. Weak, it is Stokes's point force: fluid pushed forward over a whole hemisphere and drawn in behind. Strong, it is Schlichting's slender jet, with fluid drawn in from every direction outside a narrowing cone. One constant joins them, and it says how strong a push must be before the boundary-layer jet everyone uses is right — at the axis by a jet Reynolds number of a hundred, at the edges only by a thousand.