Concept

Barometric height — where it appears

The height of a liquid column the atmosphere will support, being the ambient pressure less the vapour pressure over the liquid's weight per unit volume. It is about ten metres for water and three-quarters of a metre for mercury, and no pump of any quality reaches past it.

Named by 5 essays across one field — each of them below, with the objects they name alongside it.

Two heights, and only one of them is in the answer. A siphon, with the two heights that get confused. The drop from the source surface to the outlet is what drives the flow: the exit speed is √(2gΔz) = 4.43 m/s and nothing else enters it. The rise to the crown decides the pressure at the top — 72.0 kPa absolute here, against an atmosphere of 101.3 — and therefore whether the column holds together at all. A siphon over a high wall and one over a kerb, draining to the same place, flow at exactly the same rate.

The siphon that does not need the air

A siphon is explained everywhere by the atmosphere pushing the liquid over the hump. The flow rate says otherwise, in the flattest way available — the height of the hump does not appear in it at all. What the atmosphere does is hold the column together, which is a different job with a different limit.

misconceptions · Siphon

The one calculation in which the atmosphere really does push. How high a partial vacuum inside the tube will raise the liquid, against the absolute pressure achieved inside it. The lift is (p_atm − p_inside)/ρg and it is capped at the barometric height of 10.11 m, because below the vapour pressure the liquid boils and pulling harder buys nothing. The horizontal lines are five crown heights: a crown below a line's intersection with the curve can be primed by suction and one above it cannot, at any pump. This is the process the running siphon's argument explicitly excluded, and it is the one where the atmospheric account is the mechanism rather than a limit.

The one place the atmosphere pushes

The height of a siphon's hump is not in its flow rate, and the atmosphere holds the column together rather than driving it. That account excludes one process by name — starting. That is the process the atmospheric account describes correctly, and it is the only one in the whole device.

misconceptions · Siphon

The source falls 6 m and the crown pressure does not move. The pressure at the crown of a draining siphon, against time, as the source level falls from the top of the tank to the end of the run, a drop of 6 m. It is flat to 1.5e-11 pascals — not nearly flat, exactly flat, because the two effects of a falling source cancel identically. Losing a metre of level shrinks the drop, which slows the flow and raises the crown pressure by half a velocity head; and it grows the rise, which lowers the crown pressure by ρg per metre. Those are the same number. So a siphon that starts will not break as it drains, however far the level falls, and the run ended because the level reached the outlet instead.

The siphon that does not break

A draining reservoir shrinks the drop and grows the rise at the same time, and the siphon's own coupling — a metre of extra drop costs a metre of hump — says a siphon should break as it empties. It does not. The two effects cancel exactly, and the crown pressure of a draining siphon is a constant that does not contain the source level at all.

misconceptions · Siphon

100 metres of water, −1.98 MPa absolute at the top. The absolute pressure up a transpiring column 100 metres tall, with the sap rising at 0.25 mm/s through conduits 40 µm across. It starts at 1.3 kPa at the root, falls by 9.79 kPa a metre for gravity and 10.02 for friction, and reaches −1.98 MPa at the top — below zero, which is not a low push but a pull. The pale line is the same column with nothing flowing. The floor is not the vapour pressure but the pore a gas bubble could be drawn through: −2.81 MPa for a 50 nm pore, which this column would reach at 142 metres. A suction pump lifting the same water from a free surface stops at 10.1 metres, because it offers the water somewhere to boil.

Where a liquid does pull

A fluid cannot pull, and the essays that settle what suction is are right about every gas and every liquid with a free surface near it. A liquid with nothing in it to boil on is another matter. Every tree taller than ten metres depends on the difference, and the floor under it is set by the size of a pore rather than by the vapour pressure.

misconceptions · Suction

Friction lends the crown 28.4 kPa, and the tank takes it back. The absolute pressure at the crown of a siphon with friction in its hose, through a whole drain, for the crown placed at three positions along the hose, against the frictionless constant of 23.01 kPa. With the crown 0.3 of the way it starts at 63.3 kPa, with the crown 0.5 along it starts at 51.5 kPa and with the crown 0.7 of the way it starts at 40.4 kPa. Every curve is above the constant, every curve falls towards it as the level falls, and every curve reaches it at the end — 23.06 kPa with a centimetre of level left. Friction never brings a siphon nearer to breaking; it lends a margin, and the draining tank returns it pascal by pascal, so the worst the crown ever sees is the frictionless value.

The margin friction lends a siphon

Without friction a draining siphon's crown pressure does not depend on the source level at all, and every real hose has friction. It turns out always to raise the crown pressure, by an amount the draining tank hands back pascal by pascal — and how much it lends is decided by where along the hose the crown sits, not by how rough or how narrow the hose is.

misconceptions · Siphon

Named alongside it

The objects these essays reach for when they reach for this one.

Absolute pressure Misconception Model limit Vapour pressure Cavitation Siphon Energy equation Hydrostatics Initial condition Liquid tension Suction Bernoulli's equation

All concepts