Concept

Corner eddy — where it appears

One of the counter-rotating eddies that fill a sharp corner in slow viscous flow when the corner is stirred from far away. Each is a fixed factor smaller and weaker than the one outside it, both factors set by the corner's angle alone, and below 146° the sequence never ends.

Named by 3 essays across one field — each of them below, with the objects they name alongside it.

45° of corner, and an infinite number of eddies in it. The creeping flow in a corner of 45 degrees, drawn from Moffatt's similarity solution. Each eddy turns the opposite way to its neighbours and is 3.17 times smaller and 1.6e+3 times weaker than the one outside it. The contour levels are rescaled inside each eddy, because they differ in strength by three orders of magnitude per step and a single set of levels would show the first and nothing else — which is itself the reason nobody has seen the third. The dividing lines between eddies are drawn where the stream function changes sign, and the dots are the centres, both found from the solved field.

The eddies nobody stirs

A slow flow past the mouth of a sharp corner does not simply fail to get in. The corner fills with an infinite sequence of counter-rotating eddies, each about three times smaller and sixteen hundred times weaker than the last, and the whole structure is decided by one complex number.

viscous · Corner

The paint pushes a scraper off the wall, and roughly as one over the square of the angle it is held at. The force the fluid exerts on a still blade at angle α to a wall sliding into the corner, per unit span over μU ln(R/ε): its component pushing the blade away from the wall and the size of its component dragging it along with the wall, towards the apex. At 10° they are 196 and 22.9; at 45°, 8.56 and 4.88; at 90°, 1.36 and 2.14; at 150°, 0.0757 and 0.924.

A scraper held flat is pushed off the wall it scrapes

A corner stirred from far away fills with an endless sequence of eddies. Drive the corner at the corner instead — let one of its walls slide under a still blade, as paint slides under a scraper — and the eddies vanish: every streamline turns once, and the stress rises into the corner without limit. G. I. Taylor solved it in 1962. The paint pushes the blade away from the wall with a force that grows as one over the square of the blade's angle, so a blade held flat rides up on what it was meant to remove, and the force is finite only because something too small to appear in the problem ends the corner.

viscous · Corner

Pressed with one load, a steeper blade leaves a thinner film, and without a land a steep one cannot float at all. The film a loaded scraper leaves on the surface, in micrometres, against the angle its face makes with the surface, at a load of 100 N per metre of span on an ink of 0.1 Pa·s moving at 5 m/s: with a flat land 0.1 mm long under the edge, and with none. With the land the film is 110 µm at 10°, 1.69 at 30° and 0.268 at 60°. Without one it is the whole gap, 145 µm at 8°, and above 44° the gap the load needs is below a ten-thousandth of a nanometre: the edge is in contact.

A pressed blade floats on its land and leaves half the gap behind

A scraper or a doctor blade is not held at a gap; it is pressed on with a load, and it rises until the liquid it lets through carries that load. Without a flat land under its edge the liquid can carry it only through the corner's logarithm, so the gap falls exponentially with the load, and a blade steeper than about forty-four degrees cannot float at a working load at all — its edge is in contact. Give it a land a tenth of a millimetre long and the film becomes half the gap, falls as one over the load, and is a quarter of a micrometre at sixty degrees. The land is also why a blade's film grows as its edge wears.

viscous · Corner

Named alongside it

The objects these essays reach for when they reach for this one.

Creeping flow Model limit The no-slip condition Viscosity Lubrication Similarity solution Streamline Continuum Dissipation Dividing streamline Eigenvalue Film thickness

All concepts